Radio-shack TAD-1026 Manual de usuario

Cat. No. 43-786OWNER’S MANUALPlease read before using this equipment.TAD-1026Digital AnsweringSystem Telephonewith Dual Announcements43-786.fm Page 1

10Directly on a WallFor this mounting method, you need twoflat-head wood screws (not supplied)with heads that fit into the keyhole slotson the bottom

111. Set T/P to T.2. Lift the handset and listen for a dialtone.3. Press any number other than 0. Note: If your phone system requiresthat you dial an

122. To change the day of the week, re-peatedly press MEMO to movebackward or CODE to move for-ward until the TAD announces thedesired day of the week

13TELEPHONE OPERATIONPlace and answer phone calls on theTAD-1026 as you would with any otherphone. Read this section to learn aboutthe phone’s special

14USING FLASHFLASH performs the electronic equiva-lent of a switchhook operation for specialservices, such as Call Waiting.For example, if you have Ca

15To release the line from hold andcontinue your phone conversation,pick up the handset or anotherphone’s handset that is on the sameline.• Hold the h

16Notes: • If you make a mistake, hold downthe switchhook for a few sec-onds. Then release the switch-hook and begin again from Step2. • You can store

17Dialing a Stored NumberTo dial a number stored in memory, liftthe handset and do one of the following:• For priority memory numbers, pressM1, M2, or

18ANSWERING SYSTEM OPERATIONRECORDING THE OUTGOING MESSAGESBefore you can set the TAD to answercalls and record messages, you mustrecord the outgoing

19Important: Do not tell callers thatyou are not home. Instead, say thatyou cannot come to the phone rightnow. 3. When you finish recording, pressSTOP

2FEATURESYour RadioShack TAD-1026 Digital An-swering System Telephone with DualAnnouncements is a combination multi-feature telephone and high quality

20SETTING THE TAD TO ANSWER CALLSTo Answer and RecordTo turn on the TAD-1026’s answeringsystem and set it to answer calls andrecord messages, press AN

21If the TAD’s memory is full (FL appears),the TAD answers the call after 8 ringsand plays the announcement-only mes-sage (OGM2).SCREENING CALLSTo scr

22To play only new messages, hold downPLAY for 2 seconds. (If there are no newmessages stored, the TAD says, “Youhave no new messages.”) To adjust the

23To delete all messages, hold down DE-LETE while playback is stopped. TheTAD sounds a long beep and dL ap-pears. The TAD deletes all messagesexcept t

24To play back a recorded call, simply playback your messages.USING CALL BREAK-THROUGHIf you screen your calls but want to besure to know when calls c

25CHANGING THE REMOTE OPERATION SECURITY CODEThe remote operation security code ispreset to 784, but you can change it byfollowing these steps.Note: B

26REMOTE OPERATIONYou can operate the TAD-1026’s an-swering system from almost any touch-tone phone, or from a rotary phone usinga pocket tone-dialer

27USING REMOTE COMMANDSTo use the remote commands, you mustenter the remote operation security codewithin 8 seconds after the TAD answersthe call. Aft

2828TROUBLESHOOTINGIf you experience problems with your TAD, try the suggestions in this section. If youstill have problems, contact your local RadioS

2929CARE AND MAINTENANCEYour RadioShack TAD-1026 Digital Answering System Telephone with Dual-Announcements is an example of superior design and craft

3Toll Saver — lets you avoid unneces-sary long-distance charges when youcall by long-distance to check messag-es.Adjustable Ring Number — lets youset

30THE FCC WANTS YOU TO KNOWIn the unlikely event that your phonecauses problems on the phone line, thephone company can temporarily discon-tinue your

31NOTES43-786.fm Page 31 Monday, August 16, 1999 8:02 AM

RADIOSHACKA Division of Tandy CorporationFort Worth, Texas 761029A7 Printed in ChinaLimited One-Year WarrantyThis product is warranted by RadioShack a

4This TAD is ETL listed to UL standardsand meets all applicable FCC standards. This symbol is intended to alert you tothe presence of uninsulated da

55CONTENTS Installation ... 7Installing the

6Deleting Messages ... 20Recording a Memo ...

7INSTALLATIONINSTALLING THE BACKUP BATTERYThe TAD-1026’s answering system re-quires AC power to operate. However, ifAC power fails or you unplug the T

8wiring for you. The USOC number of thejack to be installed is RJ11C, or RJ11Wfor a wall plate jack.Caution: The supplied adapter supplies9 volts AC,

9On a Wall Plate1. Plug one end of the supplied shortmodular cord into the TEL. LINE jackon the top of the TAD. 2. Route the cord into the groove onth